Characteristic parameters of stand-alone photovoltaic (PV) systems.

رقم المستند: NL IEC 61194 : 2003
القطاع: Electrical Engineering
TC: NL TC IRI
ICS:
This International Standard defines the major electrical, mechanical and environmental parameters for the description and performance analysis of stand-alone photovoltaic systems. The parameters as listed are presented in a standard format for the purposes of procurement and performance analysis: - measurement of short - and long-term on-site photovoltaic-system performance; - comparison between on-site measured and projected performance, both extrapolated to standard test conditions (STC). Specialized documents related to specific applications and/or to specific uses (designing, performance prediction and measurement) may be issued, if necessary. NOTE - The minimum requirements, when applicable, are represented in boxes in the figures and the text. Recommended optional requirements are also given. Example UN nominal voltage minimum requirement W Weight optional requirement The numbering of subclauses is arbitrary and may not be the same for specific data sheets. 2003 EN/FR 35000.00 0 276 289 C NL IEC 61196 1 : 2006 NL TC IRI 33.120.10 60.60 Electrical Engineering RADIO-FREQUENCY CABLES – Part 1: Generic specification – General, definitions, requirements and test methods Specifies the general requirements, the definitions and the requirements for the design and test methods of coaxial communication cables. 2006 EN/FR 25000.00 0 277 290 C NL IEC 61196 3 1 : 2006 NL TC IRI 33.120.10 60.60 Electrical Engineering Radio-frequency cables- Part 3: Coaxial cables for digital communication in horizontal floor wiring- Section 1: Detail specification for cables of 500m reach and up to 10 Mb/s This publication supersedes IEC 61196-2-1. Look inside 2006 EN/FR 25000.00 0 278 291 C NL IEC 61196 3 2 : 2006 NL TC IRI 33.120.10 60.60 Electrical Engineering Radio-frequency cables- Part 3-2: Coaxial cables for digital communication in horizontal floor wiring: Detail specification for coaxical cables with solid dielectric for local area networks for 185 m reach and up to 10 Mb/s Relates to the subfamily of coaxial cables for digital communication. Should be used together with IEC 61196-1 and IEC 61196-3. Gives subfamily requirements and severities to be applied. 2006 EN/FR 35000.00 0 279 292 C NL IEC 61196 3 3 : 2006 NL TC IRI 33.120.10 60.60 Electrical Engineering Radio-frequency cables- Part 3-3: Coaxial cables for digital communication in horizontal floor wiring: Detail specification for coaxical cables with foamed dielectric for local area networks of 185 m reach and up to 10 Mb/s Relates to the subfamily of coaxial cables for digital communication. Should be used together with IEC 61196-1 and IEC 61196-3. Gives subfamily requirements and severities to be applied 2006 EN/FR 35000.00 0 280 293 C NL ISO 6743 99 : 2016 NL TC 28 75.100 60.60 Petroleum and related Technologies Lubricants, industrial oils and related products (class L) -- Classification -- Part 99: General This part of ISO 6743 establishes a general system of classification, which applies to lubricants, industrial oils and related products, designated by the prefix letter “L”. Within class L, 18 families of products are defined, according to the application areas of each, so as to cover, as much as possible, all the applications where lubricants, industrial oils and related products are used. The detailed classification of each family is given in other parts of ISO 6743. The classification only applies to new products. 2016 English 25000.00 1 281 294 C NL ISO 12922 : 2016 NL TC 28 75.120 60.60 Petroleum and related Technologies Lubricants, industrial oils and related products (class L) -- Family H (Hydraulic systems) -- Specifications for hydraulic fluids in categories HFAE, HFAS, HFB, HFC, HFDR and HFDU This International Standard specifies the minimum requirements of unused fire-resistant and less-flammable hydraulic fluids for hydrostatic and hydrodynamic systems in general industrial applications. It is not intended for use in aerospace or power-generation applications, where different requirements apply. It provides guidance for suppliers and end users of these less hazardous fluids and to the manufacturers of hydraulic equipment in which they are used. Of the categories covered by ISO 6743-4, which classifies the different types of fluids used in hydraulic applications, only the following are detailed in this International Standard: HFAE, HFAS, HFB, HFC, HFDR and HFDU. Types HFAE, HFAS, HFB, HFC and HFDR are “fire-resistant” fluids as defined by ISO 5598. Most HFDU fluids, while displaying an improvement in combustion behaviour over mineral oil, fall outside this definition and are more appropriately considered “less-flammable” fluids. NOTE For the purposes of this Internatio 2016 English 25000.00 1 282 295 C NL ISO 19378 : 2016 NL TC 28 75.100 60.60 Petroleum and related Technologies Lubricants, industrial oils and related products (class L) -- Machine-tool lubricants -- Categories and specifications This International Standard provides the manufacturers and users of machine tools with criteria for the choice among the various categories of lubricants and gives specifications for these lubricants. This International Standard facilitates the application of ISO 5169 relating to the presentation of lubrication instructions for machine tools. 2016 English 25000.00 1 283 296 C NL ISO IEC 7811 6 : 2016 NL JTC 1 35.240.15 60.60 Information Technology. Office Machines Identification cards — Recording technique — Part 6: Magnetic stripe — High coercivity This International Standard defines the characteristics for identification cards as defined in Clause 4 of this part of ISO/IEC 7811 and the use of such cards for international interchange. This part of ISO/IEC 7811 specifies requirements for a high coercivity magnetic stripe (including any protective overlay) on an identification card, the encoding technique, and coded character sets. It takes into consideration both human and machine aspects and states minimum requirements. Coercivity influences many of the quantities specified in this part of ISO/IEC 7811 but is not itself specified. The main characteristic of the high coercivity magnetic stripe is its improved resistance to erasure. This is achieved with minimal probability of damage to other magnetic stripes by contact while retaining read compatibility with magnetic stripes as defined in ISO/IEC 7811-2. This International Standard provides criteria to which cards are to perform. No consideration is given within this Internat 2016 English 35000.00 0 284 297 C NL EN 12085 : 2003 NL TC EO 91.120.10 60.60 Mechanical Systems and Components for General Use Thermal insulating products for building applications - Determination of linear dimensions of test specimens This European Standard specifies the characteristics and choice of measuring equipment and the procedure for determining the linear dimensions of test specimens which are taken from thermal insulating products. The procedures for measuring the dimensions of full size products are specified in EN 822 and EN 823. 2003 English; French 25000.00 0 285 298 C NL EN 12086 : 2003 NL TC EO 91.120.10 60.60 Mechanical Systems and Components for General Use Thermal insulating products for building applications - Determination of water vapour transmission properties This European Standard specifies the equipment and procedures for determining the water vapour transmission rate, water vapour permeance and water vapour permeability of test specimens in the steady state under different sets of specified test conditions. It is applicable to thermal insulating products. It is intended to be used for homogeneous materials and for products which may contain integral skins or facings of different material(s). A material is considered to be homogeneous, with regard to mass distribution, if its density is approximately the same throughout, i.e. if the measured density values are close to its mean density. This test method is not normally used for determining the water vapour transmission properties of single, separate vapour barriers (of high diffusion resistance), such as prefabricated films, foils, membranes or sheets, due to the long duration of the test. For products with a vapour retarder or barrier with a water vapour diffusion equivalent air layer thickness sd  1 000 m (see 3.6) other test methods e.g. IR-detection can be used for measuring the single separate vapour retarder or barrier, provided that the results obtained are in the same range as the values measured in accordance with this standard. The water vapour transmission rate and permeance values are specific to the test specimen (i.e. the product) thickness tested. For homogeneous products, the water vapour permeability is a property of the material. 2003 English; French 25000.00 0 286 299 C NL EN 12087 : 2003 NL TC EO 91.120.10 60.60 Mechanical Systems and Components for General Use Thermal insulating products for building applications - Determination of long term water absorption by immersion This European Standard specifies the equipment and procedures for determining the long-term water absorption of test specimens. It is applicable to thermal insulating products. This European Standard specifies two options: - Method 1 - partial immersion - Method 2 - total immersion The long-term water absorption by partial immersion is intended to simulate the water absorption caused by long term water exposure. The long-term water absorption by total immersion is not directly related to the conditions on site, but has been recognised as a relevant condition of test for some products in some applications. 2003 English; French 25000.00 0 287 300 C NL EN 12088 : 2003 NL TC EO 91.120.10 60.60 Mechanical Systems and Components for General Use Thermal insulating products for building applications - Determination of long term water absorption by diffusion This European Standard specifies the equipment and procedures for determining the long-term water absorption of test specimens by diffusion. It is applicable to thermal insulating products. It is intended to simulate the water absorption of products subjected to high relative humidities, approximating to 100 %, on both sides and subjected to a water vapour pressure gradient for a long period of time e.g. inverted roof or unprotected ground insulation. The test is not applicable for all types of thermal insulating products. The product standard should state for which of its products, if any, this test is applicable. NOTE For unprotected ground insulation, the temperature of 50 C might be replaced by a lower temperature, when more data is available. 2003 English; French 25000.00 0 288 301 C NL EN 12089 : 2003 NL TC EO 91.120.10 60.60 Mechanical Systems and Components for General Use Thermal insulating products for building applications - Determination of bending behaviour This European Standard specifies the equipment and procedures for determining the bending behaviour of full size products (Method A) and test specimens (Method B) under the action of three-point loading. It is applicable to thermal insulating products. The test is designed to determine the bending strength of products and their deflection at a given load. The method can be used to determine the resistance of the product to bending stresses during transport and application. 2003 English; French 25000.00 0 289 302 C NL EN 12090 : 2003 NL TC EO 91.120.10 60.60 Mechanical Systems and Components for General Use Thermal insulating products for building applications - Determination of shear behaviour This European Standard specifies the equipment and procedures for determining shear behaviour. It is applicable to thermal insulating products. NOTE The tests described in this standard do not determine pure shear behaviour, but measure the effects of applying two opposite parallel forces to the major faces of the test specimen. The test is however called shear in this text by convention. The application of a force tangentially to the major surface of the test specimen is considered to represent more closely the stresses imposed upon thermal insulation products in many building applications, particularly walls, than other methods of measuring shear performance e.g. bending tests. 2003 English; French 25000.00 0 290 303 C NL EN 12091 : 2003 NL TC EO 91.120.10 60.60 Mechanical Systems and Components for General Use Thermal insulating products for building applications - Determination of freeze-thaw resistance This European Standard specifies the equipment and procedures for determining the effect of successive cycling from dry conditions at -20 °C to wet conditions at 20 °C on the mechanical properties and moisture content of the product. It is applicable to thermal insulating products. It is intended to simulate freeze-thaw effects on thermal insulating products which are frequently exposed to water and low temperature conditions, e.g. inverted roofs and unprotected ground insulation. This test method is not recommended for all thermal insulating products. If relevant, the product standards will state for which products this standard is applicable. 2003 English; French 25000.00 0 291 304 C NL EN 12098 1 : 2006 NL TC EO 91.140.10 60.60 Mechanical Systems and Components for General Use Controls for heating systems - Part 1: Outside temperature compensated control equipment for hot water heating systems This European Standard applies to electronic control equipment for heating systems with water as the heating medium and a supply water temperature up to 120 °C. This control equipment controls the distribution and/or the generation of heat in relation to the outside temperature and time and other reference variables. This standard covers also controllers that contain an integrated optimum start or an optimum start-stop control function. Safety requirements on heating systems remain unaffected by this standard. The dynamic behaviour of the valves and actuators are not covered in this standard. A multi-distribution and/or multi-generation system needs a coordinated solution to prevent undesired interaction and is not part of this standard. Table 1 shows the relative position of this standard within the set of EPB standards in the context of the modular structure as set out in prEN ISO 52000 1. NOTE 1 In prCEN ISO/TR 52000 2 the same table can be found, with, for each module, the numbers of the relevant EPB standards and accompanying technical reports that are published or in preparation. NOTE 2 The modules represent EPB standards, although one EPB standard may cover more than one module and one module may be covered by more than one EPB standard, for instance a simplified and a detailed method respectively. 2006 English; French 35000.00 0 292 307 C NL EN 12200 1 : 2007 NL TC IRI 23.040.01 60.60 Construction Materials and Building Plastics rainwater piping systems for above ground external use – Unplasticized Poly-Vinyl-Chloride (PVC-U) – Part 1: Specificatons for Pipes, Fittings & the System This European Standard specifies the requirements for pipes, fittings, brackets and the system of unplasticized poly(vinyl chloride) (PVC-U) intended for use as above-ground external rainwater piping systems. It also specifies: a) The requirements for metallic brackets. b) Both solid wall pipes and fittings, (i.e. product manufactured from a single layer), as well as solid wall multi-layer pipes. c) The test parameters for the test methods referred to in this standard. Pipes can be used in conjunction with fittings and brackets of acrylic materials provided these polymers meet the performance requirements of this standard. The products are usually used in conjunction with gutters conforming to EN 607 [1]. They are not intended for use with products conforming to EN 612 [2]. This standard is applicable to PVC-U rainwater systems of circular, square, rectangular or any other shape with sealed (rubber ring or solvent cement) or unsealed joints. This standard covers a range of pipes and fittings sizes. NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selections from the size range to take into account their particular requirements and any relevant national regulations and installation practices or codes. NOTE 2 The term rainwater" in this standard is used also to encompass "surface water" (as defined in EN 752 [6]) run-off from buildings.