Document Number:
NL EN 13240 : 2009
Sector:
Construction Materials and Building
Status:
C
Production Year:
2009
Price:
50000.0000
This Standard is applicable to non-mechanically fired appliances whose primary function is to provide heat into the space in which they are installed and which are listed under categories 1a and 2a of table 1 of prEN 13240. Additionally, where fitted with a boiler, they also provide domestic hot water and/or central heating. These appliances may burn naturally occurring or manufactured solid mineral fuels, peat briquettes, natural or manufactured wood logs and biomass based products which are in the form of an identifiable consistent product or be multi-fuel in accordance with the appliance manufacturer's instructions. This standard is not applicable to appliances having fan assisted combustion air.
Document Number:
NL ISO 19338 : 2009
Sector:
Construction Materials and Building
Status:
C
Production Year:
2009
Price:
35000.0000
This International Standard provides performance and assessment requirements for design standards of structural concrete. It can be used for international harmonization of design and construction requirements. This International Standard includes a) requirements, which define the required structural concrete performance, b) criteria, which give means for expressing the requirements, and c) assessment clauses, which give acceptable methods of verifying the specific criteria.
Document Number:
NL ISO 24450 : 2009
Sector:
Metrology and Measurement. Physical Phenomena
Status:
C
Production Year:
2009
Price:
25000.0000
This International Standard specifies requirements and dimensions for an internationally acceptable series of conical flasks and of flat-bottom and round-bottom flasks with wide neck for general laboratory purpose. The flasks are provided for — direct use in laboratory, fitting together with other equipment for general laboratory purposes; — further work up to other products. NOTE For narrow-necked boiling flasks, ISO 1773 applies. For boiling flasks with conical ground joints, see ISO 4797.
Document Number:
NL EN 60335 2 2 : 2009
Sector:
Electrical Engineering
Status:
C
Production Year:
2009
Price:
35000.0000
This International Standard deals with the safety of electric vacuum cleaners and water suction cleaning appliances for household and similar purposes, including vacuum cleaners for animal grooming, their rated voltage being not more than 250 V. It also applies to centrally-sited vacuum cleaners and automatic battery-powered cleaners. This standard also applies to motorized cleaning heads and current-carrying hoses associated with a particular vacuum cleaner. Appliances not intended for normal household use, but which nevertheless may be a source of danger to the public, such as appliances intended to be used by laymen in shops and other premises for normal housekeeping purposes, are within the scope of this standard. NOTE 1 Examples of such appliances are appliances intended to be used for normal housekeeping purposes in hotels, offices, schools, hospitals and similar premises. As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account – the use of appliances by young children or infirm persons without supervision; – playing with the appliance by young children. NOTE 2 Attention is drawn to the fact that – for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary; – in many countries additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour, the national water supply authorities and similar authorities. NOTE 3 This standard does not apply to – appliances intended exclusively for industrial purposes; – appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas). "
Document Number:
NL EN 60335 2 5 : 2009
Sector:
Electrical Engineering
Status:
C
Production Year:
2009
Price:
35000.0000
"This clause of Part 1 is replaced by the following. This International Standard deals with the safety of electric dishwashers for household and similar purposes that are intended for washing and rinsing dishes, cutlery and other utensils, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances. Appliances intended for normal household and similar use and that may also be used by laymen in shops, in light industry and on farms, are within the scope of this standard. However, if the appliance is intended to be used professionally for washing and rinsing dishes and cutlery and other utensils that are used for commercial purposes, the appliance is not considered to be for household and similar use only. As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account – persons (including children) whose • physical, sensory or mental capabilities; or • lack of experience and knowledge prevents them from using the appliance safely without supervision or instruction; – children playing with the appliance. NOTE 101 Attention is drawn to the fact that – for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary; – in many countries additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour, the national water supply authorities and similar authorities. NOTE 102 This standard does not apply to – commercial electric dishwashing machines (IEC 60335-2-58); – appliances intended for industrial purposes; – appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas)"
Document Number:
NL EN 60335 2 6 : 2009
Sector:
Electrical Engineering
Status:
C
Production Year:
2009
Price:
35000.0000
This clause of Part 1 is replaced by the following. This International Standard deals with the safety of stationary electric cooking ranges, hobs, ovens and similar appliances for household use, their rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral, and 480 V for other appliances. NOTE 101 Examples of appliances that are within the scope of this standard are – griddles; – grills; – induction hobs; – pyrolytic self-cleaning ovens; – steam ovens. As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account – the use of appliances by young children or infirm persons without supervision; – playing with the appliance by young children. NOTE 102 Attention is drawn to the fact that – for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary; – in many countries additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour, the national water supply authorities and similar authorities. NOTE 103 This standard does not apply to – appliances intended for commercial catering; – appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas); – grills, toasters and similar portable cooking appliances (IEC 60335-2-9); – microwave ovens (IEC 60335-2-25). NOTE Z101 For appliances that are supplied with gas, EN 30 is also applicable. 2009 English 50000.00 1
1373 1480 C NL EN 60335 2 7 : 2009 NL TC IRI 13.120 - 97.040.50 60.60 Electrical Engineering Safety of Household and Similar Electrical Appliances - Part 2: Particular Requirements for Washing Machines This clause of Part 1 is replaced by the following. This International Standard deals with the safety of electric washing machines for household and similar use, that are intended for washing clothes and textiles, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances. NOTE 101 Washing machines also supplied with other forms of energy are within the scope of this standard. Appliances not intended for normal household use but which nevertheless may be a source of danger to the public, such as appliances intended to be used by laymen in shops, in light industry and on farms, are within the scope of this standard. NOTE 102 Examples of such appliances are washing machines for communal use in blocks of flats or in launderettes. As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account – the use of appliances by young children or infirm persons without supervision; – playing with the appliance by young children. NOTE 103 Attention is drawn to the fact that – for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary; – in many countries additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour, the national water supply authorities and similar authorities; – for appliances having a separate spin container for water extraction, IEC 60335-2-4 is also applicable; – for appliance having a drying function, IEC 60335-2-11 is also applicable. "" NOTE 104 This standard does not apply to – appliances intended exclusively for industrial purposes; – appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas)."
Document Number:
NL EN 60335 2 9 : 2009
Sector:
Electrical Engineering
Status:
C
Production Year:
2009
Price:
35000.0000
This International Standard deals with the safety of electric portable appliances for household purposes that have a cooking function such as baking, roasting and grilling, their rated voltage being not more than 250 V. NOTE 101 Examples of appliances that are within the scope of this standard are – barbecues for indoor use; – breadmakers; – contact grills (griddles); – cookers; – food dehydrators; – hotplates; – portable ovens; – raclette grills; – radiant grills; – roasters; – rotary grills; – rotisseries; – toasters; – waffle irons; Examples are illustrated in Figure 101. As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account – the use of appliances by young children or infirm persons without supervision; – playing with the appliance by young children. NOTE 102 Attention is drawn to the fact that – for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary; – in many countries additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour and similar authorities. NOTE 103 This standard does not apply to – stationary ovens and stationary grills (IEC 60335-2-6); – warming plates (IEC 60335-2-12); – frying pans and deep fat fryers (IEC 60335-2-13); – microwave ovens (IEC 60335-2-25); – barbecues for outdoor use (IEC 60335-2-78); – appliances intended for commercial catering; – appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas).
Document Number:
NL EN 60335 2 11 : 2009
Sector:
Electrical Engineering
Status:
C
Production Year:
2009
Price:
25000.0000
This clause of Part 1 is replaced by the following. This International Standard deals with the safety of electric tumble dryers intended for household and similar purposes, their rated voltage being not more than 250 V for singlephase appliances and 480 V for other appliances. NOTE 101 This standard applies to the drying function of washing machines having a drying cycle. Appliances not intended for normal household use but which nevertheless may be a source of danger to the public, such as appliances intended to be used by laymen in shops, in light industry and on farms are within the scope of this standard. NOTE 102 Examples of such appliances are tumble dryers for communal use in blocks of flats or in launderettes. As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account – the use of appliances by young children or infirm persons without supervision; – playing with the appliance by young children. NOTE 103 Attention is drawn to the fact that – for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary; NOTE 104 This standard does not apply to – appliances intended exclusively for industrial purposes; – appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas) 2009 English 35000.00 0
1376 1483 C NL EN 60335 2 13 : 2009 NL TC IRI 13.120 60.60 Electrical Engineering Safety of Household and Similar Electrical Appliances - Part 2: Particular Requirements for Deep Fat Fryers, Frying Pans, and similar Appliances This clause of Part 1 is replaced by the following. This International Standard deals with the safety of electric deep fat fryers having a recommended maximum quantity of oil not exceeding 5 l, frying pans, woks and other appliances in which oil is used for cooking, and intended for household use only, their rated voltage being not more than 250 V. As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account – the use of appliances by young children or infirm persons without supervision; – playing with the appliance by young children. NOTE 101 Attention is drawn to the fact that – for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary; – in many countries additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour and similar authorities. NOTE 102 This standard does not apply to – deep fat fryers for commercial use (IEC 60335-2-37); – commercial multi-purpose cooking pans (IEC 60335-2-39); – appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas)"
Document Number:
NL EN 60335 2 14 : 2009
Sector:
Electrical Engineering
Status:
C
Production Year:
2009
Price:
35000.0000
This clause of Part 1 is replaced by the following. This International Standard deals with the safety of electric kitchen machines for household and similar purposes, their rated voltage being not more than 250 V. NOTE 101 Examples of appliances that are within the scope of this standard are – bean slicers; – berry-juice extractors; – blenders; – can openers; – centrifugal juicers; – churns; – citrus-fruit squeezers; – coffee mills not exceeding 500 g hopper capacity; – cream whippers; – egg beaters; – food mixers; – food processors; – grain grinders not exceeding 3 l hopper capacity; – graters; – ice-cream machines, including those for use in refrigerators and freezers; – knife sharpeners; – knives; – mincers; – noodle makers; – potato peelers; – shredders; – sieving machines; – slicing machines. Appliances intended for normal household and similar use and that may also be used by laymen in shops, in light industry and on farms, are within the scope of this standard. However, if the appliance is intended to be used professionally to process food for commercial consumption, the appliance is not considered to be for household and similar use only. NOTE 102 Use of a kitchen machine in a bed and breakfast premises, for example, is considered to be household use. EN 60335-2-14:2006 – 8 – NL EN 60335-2-14:2009 As far as is practicable, this standard deals with the common hazards presented by appliances which are encountered by all persons in and around the home. However, in general, it does not take into account – the use of appliances by young children or infirm persons without supervision; – playing with the appliance by young children. NOTE 103 Attention is drawn to the fact that – for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary; – in many countries additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour and similar authorities. NOTE 104 This standard does not apply to – slicing machines having a circular knife the blade of which is inclined at an angle exceeding 45° to the vertical; – food waste disposers (IEC 60335-2-16); – ice-cream appliances with incorporated motor compressors (IEC 60335-2-24); – kitchen machines intended for commercial purposes (IEC 60335-2-64); – kitchen machines intended for industrial purposes; – kitchen machines intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas).
Document Number:
NL EN 60335 2 16 : 2009
Sector:
Electrical Engineering
Status:
C
Production Year:
2009
Price:
25000.0000
This clause of Part 1 is replaced by the following. This International Standard deals with the safety of electric food waste disposers for household and similar purposes, their rated voltage being not more than 250 V. Appliances not intended for normal household use but that nevertheless may be a source of danger to the public, such as appliances intended to be used by laymen in shops, in light industry and on farms, are within the scope of this standard. As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account – the use of appliances by young children or infirm persons without supervision; – playing with the appliance by young children. NOTE 101 Attention is drawn to the fact that – for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary; – in many countries additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour, the national water supply authorities, and similar authorities; – the installation of food waste disposers may be restricted or not allowed. NOTE 102 This standard does not apply to – portable food waste disposers; – food waste disposers of the incinerator type; – appliances intended exclusively for industrial or commercial purposes; – appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas).
Document Number:
NL EN 60335 2 21 : 2009
Sector:
Electrical Engineering
Status:
C
Production Year:
2009
Price:
35000.0000
This clause of Part 1 is replaced by the following. This International Standard deals with the safety of electric storage water heaters for household and similar purposes and intended for heating water below boiling temperature, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances. Appliances not intended for normal household use but which nevertheless may be a source of danger to the public, such as appliances intended to be used by laymen in shops, in light industry and on farms, are within the scope of this standard. As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account – the use of appliances by young children or infirm persons without supervision; – playing with the appliance by young children. NOTE 101 Attention is drawn to the fact that – for appliances intended to be used at high altitudes, additional requirements may be necessary; – for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary; – in many countries additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour and similar authorities; – in many countries regulations exist for the installation of equipment connected to the water mains. NOTE 102 This standard does not apply to – appliances for boiling water (IEC 60335-2-15); – instantaneous water heaters (IEC 60335-2-35); – commercial dispensing appliances and vending machines (IEC 60335-2-75); – appliances intended exclusively for industrial purposes; – appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas).
Document Number:
NL IEC 60335 2 30 : 2009
Sector:
Electrical Engineering
Status:
C
Production Year:
2009
Price:
35000.0000
This clause of Part 1 is replaced by the following. This International Standard deals with the safety of electric room heaters for household and similar purposes, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances. NOTE 101 Examples of appliances that are within the scope of this standard are – convector heaters; – fan heaters; – heaters for use in greenhouses. – liquid-filled radiators; – panel heaters; – radiant heaters; – tubular heaters; Appliances not intended for normal household use but which nevertheless may be a source of danger to the public, such as appliances intended to be used by laymen in the shops, in light industry and on farms, are within the scope of this standard. As far as is practicable, this standard deals with the common hazards presented by appliances which are encountered by all persons in and around the home. However, in general, it does not take into account NOTE 102 Attention is drawn to the fact that – for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary; – in many countries additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour and similar authorities; – for appliances intended to be used in the presence of combustible dust, for example in barns or stables, additional requirements may be necessary. NOTE 103 This standard does not apply to – appliances intended exclusively for industrial purposes; – appliances intended to be used where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas); – heaters that are built into air conditioners (IEC 60335-2-40); – clothes dryers and towel rails (IEC 60335-2-43); – heaters for saunas (IEC 60335-2-53); – thermal-storage room heaters (IEC 60335-2-61); – heating appliances for breeding and rearing animals (IEC 60335-2-71); – foot warmers and heating mats (IEC 60335-2-81); – flexible sheet heating elements for room heating (IEC 60335-2-96); – heated carpets; – central heating systems; – heating cables (IEC 60800).
Document Number:
NL EN 60335 2 40 : 2009
Sector:
Electrical Engineering
Status:
C
Production Year:
2009
Price:
50000.0000
Add to the third line of the first paragraph, after the word “...motor-compressors”, the words “and hydronic room fan coils”.
Document Number:
NL EN 60335 2 59 : 2009
Sector:
Electrical Engineering
Status:
C
Production Year:
2009
Price:
25000.0000
This clause of Part 1 is replaced by the following. This International Standard deals with the safety of electric insect killers for household and similar purposes, their rated voltage being not more than 250 V. Appliances not intended for normal household use but that nevertheless may be a source of danger to the public, such as appliances intended to be used by laymen in shops, in light industry and on farms, are within the scope of this standard. As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account – the use of appliances by young children or infirm persons without supervision; – playing with the appliance by young children. NOTE 101 Attention is drawn to the fact that – for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary; – in many countries additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour and similar authorities. NOTE 102 This standard does not apply to – appliances that function by emitting vaporized chemicals; – appliances emitting ultrasonic waves; – appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas). NOTE 103 For appliances provided with discharge lamps or tungsten filament lamps, IEC 60598-1 also applies as far as is reasonable.
Document Number:
NL IEC 60335 2 66 : 2009
Sector:
Electrical Engineering
Status:
C
Production Year:
2009
Price:
35000.0000
This clause of Part 1 is replaced by the following. This International Standard deals with the safety of electric water-bed heaters and their associated control units, for household and similar purposes, their rated voltage being not more than 250 V. Appliances not intended for normal household use, but that nevertheless may be a source of danger to the public, such as appliances intended to be used in hotels, are within the scope of this standard. As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account – the use of appliances by young children or infirm persons without supervision; – playing with the appliance by young children. NOTE 101 Attention is drawn to the fact that – for appliances intended to be used in vehicles or on board ships or in aircraft, additional requirements may be necessary; – in many countries additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour, the national water supply authorities and similar authorities. NOTE 102 This standard does not apply to appliances – for medical purposes (IEC 60601); – intended for immersion in water during use.
Document Number:
NL IEC 60335 2 66 A1 : 2009
Sector:
Electrical Engineering
Status:
C
Production Year:
2009
Price:
25000.0000
Replace the two dashed items in the fourth paragraph by the following: – persons (including children) whose • physical, sensory or mental capabilities; or • lack of experience and knowledge prevents them from using the appliance safely without supervision or instruction; – children playing with the appliance.
Document Number:
NL EN 60335 2 80 : 2009
Sector:
Electrical Engineering
Status:
C
Production Year:
2009
Price:
25000.0000
This clause of Part 1 is replaced by the following. This International Standard deals with the safety of electric fans for household and similar purposes, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances. NOTE 101 Examples of fans that are within the scope of this standard are – ceiling fans; – duct fans; – partition fans; – pedestal fans; – table fans. This standard also applies to separate controls supplied with fans. Appliances not intended for normal household use but which nevertheless may be a source of danger to the public, such as appliances intended for use in shops, in light industry and on farms, are within the scope of this standard. As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account – the use of appliances by young children or infirm persons without supervision; – playing with the appliance by young children. NOTE 102 Attention is drawn to the fact that – for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary; – in many countries additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour and similar authorities. NOTE 103 This standard does not apply to – appliances intended exclusively for industrial purposes; – appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas); – fans incorporated in other appliances.
Document Number:
NL EN 60335 2 84 : 2009
Sector:
Electrical Engineering
Status:
C
Production Year:
2009
Price:
35000.0000
This clause of Part 1 is replaced by the following. This International Standard deals with the safety of electric toilets in which excrement is stored, dried or destructed, their rated voltage being not more than 250 V. NOTE 101 Electric toilets may be used to process garbage such as paper and food waste. This standard also applies to electric equipment for use with conventional toilets. NOTE 102 Examples of such electric equipment are – automatic seat covering devices; – chopping units; – heated seats; – pumping units; – water heaters for shower units. As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account young children playing with the appliance. NOTE 103 Attention is drawn to the fact that – for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary; – in many countries additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour, the national water supply authorities and similar authorities. NOTE 104 This standard does not apply to – appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas); – chemical toilets; – toilets in which excrement is destructed by combustion.
Document Number:
NL EN 60335 2 98 : 2009
Sector:
Electrical Engineering
Status:
C
Production Year:
2009
Price:
25000.0000
This clause of Part 1 is replaced by the following. This International Standard deals with the safety of electric humidifiers for household and similar use, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances. NOTE 101 Examples of appliances that are within the scope of the standard are – appliances that atomize water; – appliances that evaporate water by heating; – appliances that blow air through a moist element. Appliances that are not intended for normal household use, but that nevertheless may be a source of danger to the public, such as appliances intended to be used by laymen in shops, in light industry and on farms, are within the scope of this standard. As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account – the use of appliances by young children or infirm persons without supervision; – playing with the appliance by young children. NOTE 102 Attention is drawn to the fact that – for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary; – in many countries additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour and similar authorities. NOTE 103 This standard does not apply to – humidifiers intended for use with heating, ventilation or air-conditioning systems (IEC 60335-2-88); – appliances for medical purposes (IEC 60601); – appliances intended exclusively for industrial purposes; – appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas).
Document Number:
NL ISO 1392 : 2009
Sector:
chemical Technology
Status:
C
Production Year:
2009
Price:
25000.0000
This International Standard specifies a general method for the determination of crystallizing points in the range from about - 50 to about + 250 °C. The crystallizing point can be determined directly on the sample as received, or on the dried sample, or on both. In which of these conditions the sample is to be tested and, if the determination is to be made with the dried sample, what method of drying is to be used, will be stated in the specific test method for each material.
Document Number:
NL ISO 1768 : 2009
Sector:
Metrology and Measurement. Physical Phenomena
Status:
C
Production Year:
2009
Price:
15000.0000
This International Standard specifies, for use in the preparation of measurement tables for liquids, a conventional value for the thermal cubic expansion coefficient of glass hydrometers. It states how the indications of hydrometers having a thermal cubic expansion coefficient differing from the recommended conventional value may be corrected for use in connection with measurement tables in the construction of which the conventional value has been used.
Document Number:
NL ISO 1770 : 2009
Sector:
Metrology and Measurement. Physical Phenomena
Status:
C
Production Year:
2009
Price:
25000.0000
This International Standard specifies requirements for two series of inexpensive "commercial quality" liquid-in-glass thermometers of the solid-stem type suitable for general purpose use in industry, schools and laboratories when great accuracy of measurement is not required : a) a series designated A to H, in which nominal ranges and maximum overall lengths are specified but which may not be acceptable for testing by a national verification laboratory; b) a series designated J to W of greater accuracy than in a) and with specified ranges and a tolerance on overall length, which may be acceptable for testing by a national verification laboratory. The temperature range covered by each series is from - 100 °C to + 500 °C.
Document Number:
NL ISO 1771 : 2009
Sector:
Metrology and Measurement. Physical Phenomena
Status:
C
Production Year:
2009
Price:
25000.0000
The specified requirements deal with a series of inexpensive "commercial" liquid-in-glass thermometers, when great accuracy of measurement is not required. The temperature range covered is from -100 degrees centigrade to +500 degress Centigrade. Temperature scale, immersion, liquid- and gasfilling and the properties of glass are specified. Details of the construction with graduation and marking and expansion volume are described.
Document Number:
NL ISO 1772 : 2009
Sector:
Metrology and Measurement. Physical Phenomena
Status:
C
Production Year:
2009
Price:
25000.0000
Three types of crucibels are specified: Type 1, low form, type 2 medium form and type 3 tall form bases an a height/diameter ratio of 0,63; 0,8 and 1,25 resp. Further two types of lid are described: type D, a lid of slightly domed shape and typ R, a recessed lid. Material and construction are specified, shape and dimensions are shown in drawings and in a table.
Document Number:
NL ISO 1773 : 2009
Sector:
Metrology and Measurement. Physical Phenomena
Status:
C
Production Year:
2009
Price:
25000.0000
This International Standard specifies requirements and dimensions for an internationally acceptable series of conical flasks and of flat-bottom and round-bottom flasks for general laboratory purposes. The flasks are provided for — direct use in a laboratory, fitting together with other equipment for general laboratory purposes; — further work up to other products. NOTE — Annex A lists additional International Standards for other general-purpose laboratory glassware.
Document Number:
NL ISO 1775 : 2009
Sector:
Metrology and Measurement. Physical Phenomena
Status:
C
Production Year:
2009
Price:
25000.0000
This International Standard specifies requirements for a quality of porcelain suitable for all types of porcelain laboratory apparatus (including microchemical apparatus) and describes appropriate methods of test. NOTE — Some of the tests specified should, for convenience, be carried out only on the articles mentioned, the results being accepted as generally applicable to all articles manufactured under similar conditions from the same batch of material.
Document Number:
NL ISO 2211 : 2009
Sector:
chemical Technology
Status:
C
Production Year:
2009
Price:
15000.0000
This International Standard specifies a method of measuring the colour in Hazen units of liquid chemical products. It is applicable only to clear, slightly coloured liquids for which the colour characteristics are close to those of the reference platinum-cobalt scale. Such colour characteristics are generally describable as "brownish-yellow". This method is applicable whenever specified by an ISO Recommendation or International Standard relating to a given product.
Document Number:
NL ISO 5663 : 2009
Sector:
Food Technology
Status:
C
Production Year:
2009
Price:
25000.0000
1.1 Substance determined This International Standard specifies a method for the determination of nitrogen by a Kjeldahl-type method. Only trivalent negative nitrogen is determined. Organic nitrogen in the form of azide, azlne, azo, hydrazone, nitrite, nitro, nitroso, oxime or semicarbazone is not determined quantitatively. Nitrogen may be incompletely recovered from heterocyclic nitrogen compounds. 1.2 Type of sample This method is applicable to the analysis of raw, potable and waste waters. 1.3 Range A Kjeldahl nitrogen content, ϱN, of up to 10 mg, in the test portion may be determined. Using a 10 ml test portion, this corresponds to a sample concentration of up to ϱN = 1 000 mg/l. 1.4 Limit of detection A practically determined (4 degrees of freedom) limit of detection, using a 100 ml test portion, is ϱN = 1 mg/l. 1.5 Sensitivity Using a 100 ml test portion, 1,0 ml of 0,02 mol/l hydrochloric acid is equivalent to ϱN = 2,8 mg/l.
Document Number:
NL ISO 5664 : 2009
Sector:
Food Technology
Status:
C
Production Year:
2009
Price:
25000.0000
This International Standard specifies a distillation and titration method for the determination of ammonium in raw, potable and waste water.
Document Number:
NL ISO 5666 : 2009
Sector:
Food Technology
Status:
C
Production Year:
2009
Price:
35000.0000
This International Standard specifies two methods for the determination of mercury in water, for example in ground, surface and waste waters. In the method described in clause 4, tin(ll) chloride is used as reducing agent. In the method given in clause 5, sodium tetrahydroborate is used as reducing agent. The choice of the method depends on the equipment available and the matrix (see clause 3). Both methods are suitable for the determination of mercury in the concentration range from 0,l pg/I to 10 pg/l. Higher concentrations can be determined if the water sample is diluted.
Document Number:
NL ISO 5366 1 : 2009
Sector:
Health Care Technology
Status:
C
Production Year:
2009
Price:
25000.0000
This part of ISO 5366 specifies requirements for tracheostomy tubes made of plastics materials and/or rubber having inside diameters of or greater. Such tubes are primarily designed for patients who require anaesthesia, artificial ventilation or other respiratory support, but need not be restricted to these uses. This part of ISO 5366 is not applicable to specialized tubes, and does not address flammability of tracheostomy tubes.
Document Number:
NL ISO 5366 3 : 2009
Sector:
Health Care Technology
Status:
C
Production Year:
2009
Price:
25000.0000
This part of ISO 5366 gives requirements for paediatric tracheostomy tubes made of plastics materials and/or rubber having inside diameters from to . Requirements for paediatric tracheostomy tube connectors and adaptors are also given. This part of ISO 5366 is not applicable to specialized tracheostomy tubes
Document Number:
NL ISO 2590 : 2009
Sector:
chemical Technology
Status:
C
Production Year:
2009
Price:
25000.0000
Applicable to determining the quantities contained either in all the test solution or in the aliquot portion of between 1 g and 20 g that is taken for the determination. The principle bases on the reduction of the arsenic by zinc in a hydrochloric acid medium with the formation of arsine; absorption of the arsine in a solution of silver diethyldithiocarbamate in pyridine. Photometric measurement of the purplish-red colour produced by the colloidally dispersed silver at the maximum of the absorption curve at a wavelength of about 540 nm.
Document Number:
NL ISO 2718 : 2009
Sector:
chemical Technology
Status:
C
Production Year:
2009
Price:
25000.0000
Gives detailed notes on the application of the layout. Deals with the titel of the publication, the scope and field of application, describes the details of the subject of the investigation. Specifies the materials, apparatus and characteristics which are to be used. Describes the details of the sample and procedure. Specifies the expression of results particularly those which are to be observed in the test report, and that all hazards are to be grouped. They shall be given under an appropriate heading. The annex contains calculation formulae.
Document Number:
NL ISO 4793 : 2009
Sector:
Metrology and Measurement. Physical Phenomena
Status:
C
Production Year:
2009
Price:
25000.0000
This International Standard specifies a system of porosity grading, classifying and designating laboratory sintered (fritted) filters by the determination of pore size index. It is applicable to laboratory filters made of glass, vitreous silica, ceramics, metals and plastic materials. Test methods are included in annexes B and C for the determination of air permeability and uniformity of pore size, but these characteristics do not form part of the requirements of this International Standard.
Document Number:
NL ISO 5813 : 2009
Sector:
Food Technology
Status:
C
Production Year:
2009
Price:
25000.0000
This International Standard specifies an iodometric method for the determination of dissolved oxygen in water by the so-called "Winkler procedure" modified in order to make allowance for certain interferences. The iodometric method is the reference method for the determination of dissolved oxygen in water. It is applicable to all types of water having dissolved oxygen concentrations greater than 0,2 mg/l, up to double saturation of oxygen (approximately 20 mg/l), which are free from interfering substances. Readily oxidizable organic substances such as tannins, humic acid and lignins, interfere. Oxidizable sulphur compounds such as sulphides and thiourea also interfere, as do actively respiring systems which readily consume oxygen. In the presence of such substances, it is preferable to use the electrochemical probe method specified in ISO 5814. Nitrites up to a concentration of 15 mg/l do not interfere with the determination because they are destroyed by the addition of sodium azide. If oxidizing or reducing substances are present, it is necessary to make modifications to the method ; these are described in clause 9. If suspended matter, capable of fixing or consuming iodine, is present, the method may be used with the modification described in the annex, but it is preferable to use the electrochemical probe method.
Document Number:
NL ISO 5814 : 2009
Sector:
Food Technology
Status:
C
Production Year:
2009
Price:
25000.0000
This International Standard specifies an electrochemical method for the determination of dissolved oxygen in water by means of an electrochemical cell which is isolated from the sample by a gas permeable membrane. Measurement can be made either as a concentration of oxygen in milligrams per litre, percentage saturation (% dissolved oxygen) or both. The method measures oxygen in water corresponding to 1 % to 100 % saturation. However, most instruments permit measurement of values higher than 100 %, i.e. supersaturation. NOTE Supersaturation is possible when the partial pressure of oxygen is higher than in air. Especially when strong algal growth is present, supersaturation of up to 200 % and above can occur. The method measures oxygen in water with a saturation higher than 100 %, when special arrangements to prevent the outgassing of oxygen during the handling and measurement of the sample are made. The method is suitable for measurements made in the field and for continuous monitoring of dissolved oxygen, as well as measurements made in the laboratory. It is the preferred method for highly coloured and turbid waters, and also for analysis of waters not suitable for the Winkler titration method because of iron- and iodine-fixing substances, which can interfere in the iodometric method specified in ISO 5813.[1] The method is suitable for drinking waters, natural waters, waste waters, and saline waters. If used for saline waters, such as sea or estuarine waters, a correction for salinity is essential.
Document Number:
NL ISO 5815 1 : 2009
Sector:
Food Technology
Status:
C
Production Year:
2009
Price:
35000.0000
This part of ISO 5815 specifies a determination of the biochemical oxygen demand of waters by dilution and seeding with suppression of nitrification. This part of ISO 5815 is applicable to all waters having biochemical oxygen demands greater than or equal to 3 mg/l of oxygen (the limit of determination) and not exceeding 6 000 mg/l of oxygen. For biochemical oxygen demands greater than 6 000 mg/l of oxygen, the method is still applicable, but the errors caused by the necessary dilutions can influence the analytical quality of the test method and the results are to be interpreted with circumspection. The results obtained are the product of a combination of biochemical and chemical reactions. They do not have the rigorous and unambiguous character of those resulting from, for example, a single, well-defined, chemical process. Nevertheless, they provide an indication from which the quality of waters can be estimated. The test can be influenced by the presence of various substances. Those which are toxic to microorganisms, for example bactericides, toxic metals or free chlorine, will inhibit biochemical oxidation. The presence of algae or nitrifying microorganisms can produce artificially high results. Annex A describes alternative incubation periods. Annex B describes multitesting, which can be used to obtain enhanced precision or to demonstrate the presence of substances toxic to microorganisms. Annex C provides precision data.
Document Number:
NL ISO 5815 2 : 2009
Sector:
Food Technology
Status:
C
Production Year:
2009
Price:
25000.0000
This part of ISO 5815 specifies determination of the biochemical oxygen demand (BOD) of waters of undiluted samples. It is applicable to all waters having biochemical oxygen demands greater than or equal to 0,5 mg/l of oxygen (the limit of determination) and not exceeding 6 mg/l of oxygen. The results obtained are the product of a combination of biochemical and chemical reactions. They do not have the rigorous and unambiguous character of those resulting from, for example, a single, well-defined, chemical process. Nevertheless, they provide an indication from which the quality of waters can be estimated. The test can be influenced by the presence of various substances. Those which are toxic to microorganisms, for example bactericides, toxic metals or free chlorine, inhibit biochemical oxidation. The presence of algae or nitrifying microorganisms can produce artificially high results. In these situations a modification of the method may be necessary. Annex A describes alternative incubation periods. Annex B describes procedures for modification of the method by addition of seeding material, salts, inhibition of nitrification by allylthiourea (ATU) addition, neutralization, homogenization and/or filtration. These modifications may be found necessary for specific evaluations of the water quality of receiving waters. Annex C provides precision data.
Document Number:
NL ISO 5840 : 2009
Sector:
Health Care Technology
Status:
C
Production Year:
2009
Price:
50000.0000
1.1 This International Standard is applicable to all devices intended for implantation in human hearts, as a heart valve substitute. 1.2 This International Standard is applicable to both newly developed and modified heart valve substitutes and to the accessory devices, packaging and labelling required for their implantation and for determining the appropriate size of heart valve substitute to be implanted. 1.3 This International Standard outlines an approach for qualifying the design and manufacture of a heart valve substitute through risk management. The selection of appropriate qualification tests and methods are derived from the risk assessment. The tests may include those to assess the physical, chemical, biological and mechanical properties of heart valve substitutes and of their materials and components. The tests may also include those for pre-clinical in vivo evaluation and clinical evaluation of the finished heart valve substitute. 1.4 This International Standard imposes design specifications and minimum performance specifications for heart valve substitutes where adequate scientific and/or clinical evidence exists for their justification. 1.5 This International Standard excludes heart valve substitutes designed for implantation in artificial hearts or heart assist devices. NOTE A rationale for the provisions of this International Standard is given in Annex A.
Document Number:
NL ISO 4785 : 2009
Sector:
chemical Technology
Status:
C
Production Year:
2009
Price:
25000.0000
This International Standard specifies requirements and dimensions for two series of glass straight-bore stopcocks for general-purpose use. The stopcocks are defined by their nominal (bore) diameter and large end diameter and length of the ground zone. It is recommended that, in national standards, only one of the series should be specified. NOTE — Annex A lists additional International Standards for other general-purpose laboratory glassware.
Document Number:
NL ISO 4786 : 2009
Sector:
Metrology and Measurement. Physical Phenomena
Status:
C
Production Year:
2009
Price:
25000.0000
This International Standard specifies requirements for enclosed-scale adjustable-range thermometers for measuring small temperature differences not exceeding 5 C (or, exceptionally, 6 °C) within the range - 20 °C to + 140 °C. The thermometers are unsuitable for measuring absolute temperatures unless they have been compared with standard instruments immediately before use.
Document Number:
NL ISO 5790 : 2009
Sector:
chemical Technology
Status:
C
Production Year:
2009
Price:
25000.0000
This International Standard specifies a general mercurimetric method for the determination of chloride content.
Document Number:
NL 603 : 2009
Sector:
Food Technology
Status:
C
Production Year:
2009
Price:
25000.0000
تحدد هذه المواصفة القياسية الاشتراطات والتوجيهات العامة لتخزين ونقل الزيوت الخام أو المكررة والدهون المعدة للاستهلاك البشري غير المعبأة (الدكمة) لضمان تزويد المستهلك بالمنتجات الصحية. كما تشمل هذه المواصفة لائحة بالمواد المحظور نقلها في الصهاريج والخزانات المستعملة في نقل وتخزين الزيوت الخام والزيوت المكررة والدهون.
Document Number:
NL ISO 594 1 : 2009
Sector:
Health Care Technology
Status:
C
Production Year:
2009
Price:
25000.0000
Specification of the requirements for conical (Luer) fittings for use with hyperdemic syringes and needles and with certain other apparatus for medical use such as transfusion and infusion sets. It covers fittings made of rigid and semi-rigid materials and includes test methods for gauging and performance. It excludes provision for more flexible or elastomeric materials. The annex on liquid leakage is given as an example.
Document Number:
NL ISO 759 : 2009
Sector:
chemical Technology
Status:
C
Production Year:
2009
Price:
15000.0000
The method of test is applicable to products having dry residues after evaporation greater than or equal to 10 mg/kg Ä0.001 % (m/m)Ü. The principle consists in evaporation of a test portion on a water bath, and drying the residue, if any, to a constant mass in an oven at 110 °C 2 K. - Cancels and replaces ISO Recommendation R 759-1968 of which it constitutes a technical revision.
Document Number:
NL ISO 760 : 2009
Sector:
Chemical Technology
Status:
C
Production Year:
2009
Price:
25000.0000
Two methods of titration depending on whether the end point is detected visually or electrometrically are specified. The visual method is only applicable to colourless solutions but can be used when no electrometric apparatus is available. The electrometric method, whether by direct titration or back-titration, is the more accurate one and for this reason recommended. The principle of the test consists in reaction of any water present in a test portion with a solution of iodine and sulphur dioxide in a pyridine/methanol mixture (Karl Fischer reagent), previously standardized by titration with an exactly known mass of water.
Document Number:
NL ISO 6955 : 2009
Sector:
chemical Technology
Status:
C
Production Year:
2009
Price:
35000.0000
This International Standard defines specific terms for flame emission, atomic absorption and atomic fluorescence spec- troscopic analytical methods, with a view to facilitating understanding between analysts. lt takes maximum account of the existing terminology, in both French and English, in Order to achieve the greatest possible harmonization. In particular, it takes account of the IUPAC (International Union of Pure and Applied Chemistry) nomenclature.
Document Number:
NL ISO 7027 : 2009
Sector:
Food Technology
Status:
C
Production Year:
2009
Price:
25000.0000
This part of ISO 7027 specifies two quantitative methods using optical turbidimeters or nephelometers for the determination of turbidity of water: a) nephelometry, procedure for measurement of diffuse radiation, applicable to water of low turbidity (for example drinking water); b) turbidimetry, procedure for measurement of the attenuation of a radiant flux, more applicable to highly turbid waters (for example waste waters or other cloudy waters). Turbidities measured according to the first method are presented as nephelometric turbidity units (NTU). The results typically range between <0,05 NTU and 400 NTU. Depending on the instrument design, it can also be applicable to waters of higher turbidity. There is numerical equivalence of the units NTU and formazin nephelometric unit (FNU). Turbidity measured by the second method is expressed in formazin attenuation units (FAU), results typically range between 40 FAU and 4 000 FAU.
Document Number:
NL ISO 7056 : 2009
Sector:
Metrology and Measurement. Physical Phenomena
Status:
C
Production Year:
2009
Price:
25000.0000
This International Standard specifies requirements for a series of squat-form plastics beakers for laboratory use. It is applicable to beakers having a tapered or a non-tapered form. The non-tapered form may, however, have a slight taper to facilitate mould release during manufacture.